Dillon Press Enhancements
|1050 Spent Primer Chute (SKU: T1346-1050)The 1050 Spent Primer Chute™ replaces the blue plastic spent primer cup on the Dillon Super 1050 reloading press. Spent primers are routed through clear PVC tubing into any convenient waste container.||2X Powder Hopper Tube (SKU: T1277)The 2X Powder Hopper Tube™ doubles the powder capacity of the Dillon Auto Powder Measure or "Belted Magnum" Powder System.||550 Primer Track Bearing (SKU: T1571)The UniqueTek 550 Primer Track Bearing has a 1.4″ extension that supports the primer bar better. This extended support prevents the primer bar from "drooping" and binding while its in the "out" position. The UniqueTek 550 Primer Track Bearing is a drop-in replacement for the original Dillon Primer Track Bearing (part #14015) and takes just minutes to install.||550 Spent Primer Chute (SKU: T1346-550)The 550 Spent Primer Chute™ is a Spent Primer Chute for the Dillon RL 550B Press. Spent primers are routed through clear PVC tubing to any suitable container located under your reloading bench. Virtually eliminates spent primers bouncing out and onto the floor.|
|650 Live Primer Chute (SKU: T1306)The UniqueTek 650 Live Primer Chute Prevents primers from falling onto floor. It captures primers and holds them for reuse. The UniqueTek 650 Live Primer Chute is a "drop-in" replacement for the original Dillon Primer Chute (part #16210) and takes just minutes to install. (Note: May not fit certain older XL 650 presses. See product web page for complete details.)||650 Spent Primer Chute (SKU: T1346-650)The 650 Spent Primer Chute™ replaces the blue plastic spent primer cup and bracket on the Dillon 650 reloading press. Spent primers are routed through clear PVC tubing into any convenient waste container, so spent primes simply can't bounce out onto the floor! Includes 650 Primer Chute™, 3' Clear PVC Tubing and Instructions. Note: Does not fit certain older model 650 presses. See product page for details before ordering.||Arredondo Powder Drop Slide with Micrometer (SKU: T1267)The Arredondo Accessories Powder Drop Slide with our Micrometer Powder Bar Kit preinstalled. For the Dillon Precision auto powder measure. See product page to order the correct version for your press.||Bin-Shelf (SKU: T1633)The Bin-Shelf™ provides a platform to support the weight of the Cartridge Bin on Dillon XL 650 presses.|
|Bullet Seat Stem (SKU: T1561)This custom bullet seat stem contacts SWC bullets at the shoulder, yielding consistent alignment and seating of SWC bullet profiles. Works equally well with FWC bullets! Fits Dillon "New Dynamic" Pistol Seat Die. Available in .45 cal., .40 cal. and .38 cal. (See web page to select the caliber you need.)||CNC Machined 550/650 Toolheads (SKU: T1333)CNC machined toolheads for Dillon RL 550B and XL 650 reloading presses. Made from solid 6061-T6 aluminum and machined to exacting standards.||
Custom Powder Funnel (SKU: T1582)The Custom Powder Funnel supplied is precision machined from top grade 12L14 Steel and hardened to RC55+ … offering an almost unlimited life time of use. The mirror finish of this part yields minimal friction and a smoother release.
These Custom Powder Funnels work so well, you may want to use them on all your pistol cartridge toolheads … even toolheads that are not set up for a Mr. Bulletfeeder!
|Die Wrench for Dillon Presses (SKU: T1532)The best and last die wrench you'll ever need for your Dillon press. Fits Both 1″ and 1-1/8″ Die Lock Rings. Also Fits the closely spaced die lock rings on LEE progressive presses.|
|Die Wrench for Dillon SDB Press (SKU: T1604)The best and last die wrench you'll ever need for your Dillon Square Deal B press. Double box end wrench fits 3/4″ and 9/16″.||Dillon Primer Rod with Holder (SKU: T1562)Dillon Primer Rod with Holder. The Primer Rod is made from aluminum and weighs 0.52oz to give positive primer feeding. The Primer Rod has lines at 100 primers, 75 primers, 50 primers and 25 primers and is accurate to ±1 primer. Also included is a Primer Rod Holder, so when you load primers into the tube, you have a convenient place to hang the Rod. Fits on Dillon Squared Deal 'B', RL 550B, XL 650, and Super 1050 presses.||Dillon XL 650 Case Chute Extension (SKU: T1590)The Dillon XL 650 Case Chute Extension lenghtens the original cartridge ejection chute by 6.25″, allowing you to use a larger container to capture the loaded cartridges. Just set any convenient container on the bench and position it under the chute. Note: Press must be on a Strong Mount.||Floating Die 550/650 Toolheads (SKU: T1389)CNC Machined Floating Die Toolheads for Dillon 550 and 650 presses. Size Die and Bullet Seat Die are floated for improved ammunition concentricity. Available only with Toolhead Clamp Kit™ parts pre-installed.|
|Foam Grip (SKU: T1527)This foam grip cushions your hand yet provides good "feel" when seating primers. Fits both the Plastic and Aluminum Dillon Roller Handles … as well as most other press handles that are approximately 1" diameter and 4" to 5" long..||Loaded Round Counter (SKU: T1555)The UniqueTek Loaded Round Counter is an electronic counter for your Dillon press that counts only successfully loaded rounds ... not just press cycles. Can also be used on many other reloading presses that have: 1) Have a Crimp Die with an open top, and 2) Have a primer tube or similar place on which to mount the LCD Display Module.||Micrometer Powder Bar Kit (SKU: T1231)A micrometer conversion kit for the powder bar of your Dillon Auto Powder Measure.||Powder Measure Drain-N-Change Tool (SKU: T1347)Powder Measure Drain-N-Change™ Tool. Allows users of Dillon reloading presses to drain gunpowder or change powder bars without removing the powder measure from the press or toolhead.|
Powder Measure Stand Adapter (SKU: T1573)The Powder Measure Stand Adapter allows you to store your spare Dillon Powder Measure on a RL550/XL650 Toolhead Stand.*
*Dillon Toolhead Stand not included.
|Precision Powder Baffle (SKU: T1278)Pecision Powder Baffle™ upgrade for Dillon powder measures.||Primer Tube Stand (SKU: T1567)The UniqueTek Primer Tube Stand holds up to 12 primer pickup tubes, 6 on each side, in a horizontal position. The Stand has a base that is wide enough to be stable and not easily tipped over. It assembles in just seconds and can easily be dismantled to save bench space when not in use.||SDB Bullet Seat Stem (SKU: T1605)This custom bullet seat stem contacts SWC bullets at the shoulder, yielding consistent alignment and seating of SWC bullet profiles. Fits only Dillon Square Deal B (SDB) Seat Dies. Available in .45 cal. and .38 cal. (See web page to select the caliber you need.)|
|SDB Spent Primer Chute (SKU: T1346-SDB)The SDB Spent Primer Chute™ replaces the blue plastic spent primer cup on the Dillon Square Deal 'B' reloading press. Spent primers are routed through clear PVC tubing into any convenient waste container.||Shellplate Bearing Kit (SKU: T1601)The 550/650/900 Shellplate Bearing Kit smooths indexing and reduces play and wobble in the shell plate. It also reduces the "snap" when the index ball engages the shellplate … greatly reducing powder loss from cases on the shellplate.||SOLO Single Stage Press Conversion Kit (SKU: T1553)The SOLO™ Single Stage Press Conversion Kit converts your Dillon RL 550b or XL 650 press to a single stage press. This allows you to perform reloading operations that simply cannot be done using a Dillon progressive reloading press. (See product web page for details and to order the correct kit for your press.)||Swage It S550 (SKU: T1568-5)The Swage It S550 Primer Pocket Swager for the Dillon RL 550B press. Everything that you need to swage .223/5.56mm, .308/7.62mm or any other calibers that utilize small or large primers. Includes Swages for both small and large primers.|
|Swage It S650 (SKU: T1568-6)The Swage It S650 Primer Pocket Swager for the Dillon XL 650 press. Everything that you need to swage .223/5.56mm, .308/7.62mm or any other calibers that utilize small or large primers. Includes Swages for both small and large primers.||The Bin-Dam (SKU: T1359)The Bin-Dam™ fits into the front of the Cartridge Collection Bin for Dillon, LEE and RCBS reloading presses. It keeps rounds from rolling out and onto the floor when the bin gets near full. Allows use of 100% of bin's capacity. Available in three sizes to fit the cartridge collection bins for SDB/550/650 presses, the 1050 press, and for the SL 900 Shotshell Loader.||The Bullet Bin (SKU: T1446)The Bullet Bin™ is an economical alternative to the Dillon Bullet Tray. Easily holds a full 500 count box of 9mm 124grain bullets ... with room to spare.||The Original Powder Mirror (SKU: T1572)The Original Powder Mirror helps you visually inspect the powder drop in each case. If you've ever had a squib, you'll appreciate this added level of security.|
|Toolhead Clamp Kit (SKU: T1230)The UniqueTek Toolhead Clamp Kit™ enables your Dillon 550 and 650 toolheads, and RCBS Pro 2000®/Piggyback™ -3 & -4 dieplates, to be CLAMPED into the press frame. This corrects the loose fit between the toolhead and press frame, thus reducing OAL variation and improving die-to-shellplate alignment.||
Toolhead Organizer - 1050 (SKU: T1630)Organize and store all your Dillon 1050 toolhead assemblies and caliber conversion kits in one convenient place. Mounts to wall, freeing up more space on your work bench. Available in 3-post and 5-post models.
Toolhead Organizer - 550/650 (SKU: T1629)Organize and store all your Dillon 550/650 toolhead assemblies and caliber conversion kits on one convenient place. Mounts to wall, freeing up more space on your work bench. Available in 3-post and 5-post models.
||TURBO-BEARING (SKU: T1281)TURBO-BEARING® for Dillon RL 550b will smooth the indexing and reduce the play and wobble in the shell plate.|