| Items: | 0 |
| Subtotal: | $0.00 |
Dillon Press Enhancements
 .32 Cal. Wad Cutter Powder Funnel (SKU: T1672-05)Specifically designed for loading wad cutter bullets in .32 S&W Long for Bullseye competition. It provides full length case expansion for loading Hollow Base Wadcutter bullets … preventing swaging the bullet base.
|
 .32 Caliber Powder Funnels (SKU: T1672)The Custom Rifle Powder Funnel for .32 cal. pistol cartridges. Smoother interior for smooth powder flow and less powder bridging. Precision machined from top grade 12L14 Steel and hardened to RC55+. |
 .45 HTC Powder Funnel (SKU: T1740)This Powder Funnel was specially designed for loading .45 caliber cast/coated bullets sized to 0.451″ to 0.452″ OD, that would provide for minimum swaging of the bullet’s base and preventing shaving polymer bullet coatings (e.g. Hi-Tek). [T1740]
|
 .45 HTC-FB Powder Funnel (SKU: T1766)This Powder Funnel was specially designed for loading 180/185gr Flat Base SWC .45 caliber bullets sized to 0.452″ … like the Brazos Bullet Company LB-45-180-SWC-FB-LG-452. [T1766]
|
 1050 Spent Primer Chute (SKU: T1346-1050)The 1050 Spent Primer Chute™ replaces the blue plastic spent primer cup on the Dillon Super 1050 reloading press. Spent primers are routed through clear PVC tubing into any convenient waste container.
|
 2X Powder Hopper Tube (SKU: T1277)The 2X Powder Hopper Tube™ doubles the powder capacity of the Dillon Auto Powder Measure or "Belted Magnum" Powder System.
|
 38 Spl. Wadcutter Powder Funnels (SKU: T1735)These Powder Funnels are specially designed for the needs of bullsey shooters loading Double Ended Wad Cutter (DEWC) or Hollow Base Wad Cutter (HBWC) bullets in .38 Special cartridges.
|
 550 Primer Track Bearing (SKU: T1571)The UniqueTek 550 Primer Track Bearing has a 1.4″ extension that supports the primer bar better. Prevents the primer bar from "drooping" and binding while its in the "out" position. It is a drop-in replacement and takes just minutes to install. NOW with ROBAR® NP3® Plating (a Nickel/Teflon composite).
|
 550 Spent Primer Chute (SKU: T1346-550)The 550 Spent Primer Chute™ is a Spent Primer Chute for the Dillon RL 550B Press. Spent primers are routed through clear PVC tubing to any suitable container located under your reloading bench. Virtually eliminates spent primers bouncing out and onto the floor.
|
 550/750 Primer Feed Stop (SKU: T1742)This Primer Feed Stop allows you to temporarily disable the |
 650 Bearing Indexer Block (SKU: T1705)This Bearing Indexer Block provides smoother operation of the Indexer Ring on Dillon XL 650 presses. It also eliminates wear of and the need to lubricate the Indexer Ring.
|
 650 FailSafe Bracket Kit (SKU: T1677)This FailSafe Bracket is machined from 1/4″ 303 Stainless Steel. It is very strong and rigid … ensuring that your powder bar returns fully every time. Plus it features a brass shoulder washer that is held in place with set screws … ensuring that the shoulder washer can't disengage from the Failsafe Bracket!
|
 650 Live Primer Chute (SKU: T1306)The UniqueTek 650 Live Primer Chute Prevents primers from falling onto floor. It captures primers and holds them for reuse. The UniqueTek 650 Live Primer Chute is a "drop-in" replacement for the original Dillon Primer Chute (part #16210) and takes just minutes to install. (Note: May not fit certain older XL 650 presses. See product web page for complete details.)
|
 650 Primer Feed Stop Switch (SKU: T1703)This Primer Feed Stop Switch allows you to temporarily disable the XL 650 Primer System. It simply replaces the original Primer Cam and can be switched from ON to OFF in just a few seconds without any tools.
|
 650/750 Bearing Camming Pin (SKU: T1706)Bearing Camming Pin smooths operation of Case Insert Slide on Dillon |
 650/750 Case Feed Stop Switch (SKU: T1704)This Case Feed Stop Switch allows you to temporarily disable the XL 650 or XL 750 Case Feed System
|
 650/750 Spent Primer Chute (SKU: T1346-650)The 650/750 Spent Primer Chute™ replaces the blue plastic spent primer cup and bracket on Dillon XL 650 and XL 750 reloading presses. Spent primers are routed through clear PVC tubing into any convenient waste container, so spent primes simply can't bounce out onto the floor! Includes 650/750 Primer Chute™, 3' Clear PVC Tubing and Instructions. Note: Does not fit certain older model 650 presses. See product page for details before ordering.
|
 750 FailSafe Bracket Kit (SKU: T1746)This 750 FailSafe Bracket features slotted screw holes that allow the Powder Measure to be rotated enough (about 12 degrees) that the powder bar clears bullet droppers, micrometer seat dies and other extra-tall dies in Stations 3 & 4. from the Failsafe Bracket! At 1/4″ thick, it is very strong and rigid … ensuring that your powder bar returns fully every time. (T1746)
|
 9mm/.38 HTC Powder Funnel (SKU: T1736)This Powder Funnel was specially designed for loading 9mm cast/coated bullets sized to 0.358″ OD, that would provide for minimum swaging of the bullet’s base. Sized for projectiles up to 0.358″ diameter … preventing shaving polymer bullet coatings (e.g. Hi-Tek). (T1736)
|
 Arredondo Powder Drop Slide with Micrometer (SKU: T1267)The Arredondo Accessories Powder Drop Slide with our Micrometer Powder Bar Kit preinstalled. For the Dillon Precision auto powder measure. See product page to order the correct version for your press.
|
 Brass Primer Magazine Tube Ends (SKU: T1739)These Brass Primer Magazine Tube Ends replace the plastic "Flexible Orifice" on Dillon Primer Magazine Tubes for RL 550 and XL 750 presses. (T1739)
|
 Bulk Powder Feed Kit (SKU: T1676)The Bulk Powder Feed™ Kit continuously refills your powder measure, keeping your powder hopper at a constant full level. It gravity feeds gunpowder directly from an 8lb or 4lb container. |
 Bullet Seat Stem (SKU: T1561)This custom bullet seat stem contacts SWC bullets at the shoulder, yielding consistent alignment and seating of SWC bullet profiles. Works equally well with FWC bullets! Fits Dillon Pistol Seat Die. Available in .45 cal., .40 cal. and .38 cal. (See web page to select the caliber you need.)
|
 CNC Machined 550/650/750 Toolheads (SKU: T1333)CNC machined toolheads for Dillon RL 550, XL 650 and XL 750 reloading presses. Made from solid 6061-T6 aluminum and machined to exacting standards.
|
 Component Recovery Cup (SKU: T1668)Component Recovery Cup™ separates powder from bullet and case when pulling bullets. Powder drains directly back into powder measure hopper for immediate reuse.
|
 Custom Powder Funnel (SKU: T1582)The Custom Powder Funnel supplied is precision machined from top grade 12L14 Steel and hardened to RC55+ … offering an almost unlimited life time of use. The mirror finish of this part yields minimal friction and a smoother release.These Custom Powder Funnels work so well, you may want to use them on all your pistol cartridge toolheads … even toolheads that are not set up for a Mr. Bulletfeeder! |
 Die Wrench for Dillon Presses (SKU: T1532)The best and last die wrench you'll ever need for your Dillon press. Fits Both 1″ and 1-1/8″ Die Lock Rings.
|
 Die Wrench for Dillon SDB Press (SKU: T1604)The best and last die wrench you'll ever need for your Dillon Square Deal B press. Double box end wrench fits 3/4″ and 9/16″.
|
 Dillon Primer Rod with Holder (SKU: T1562)Dillon Primer Rod with Holder. The Primer Rod is made from aluminum and weighs 0.52oz to give positive primer feeding. The Primer Rod has lines at 100 primers, 75 primers, 50 primers and 25 primers and is accurate to ±1 primer. Also included is a Primer Rod Holder, so when you load primers into the tube, you have a convenient place to hang the Rod. Fits on Dillon Squared Deal 'B', RL 550, XL 650, XL 750, RL 1050, Super 1050 and RL 1100 presses.
|
 Extended 550 Shellplate Bolt (SKU: T1737)An Extended Shellplate Bolt for Dillon RL 550 presses with bearing kits installed. (T1737)
|
 Extended Die Lock Nuts (SKU: T1745)Extended die lock nuts for when you need to put the die lock nut on the bottom of the toolhead. A 0.155″ shoulder gets the hex nut corners clear of the press frame. (T1745)
|
 Floating Die 550/650 Toolheads (SKU: T1389)CNC Machined Floating Die Toolheads for Dillon RL 550, XL 650 and XL 750 presses. Size Die and Bullet Seat Die are floated for improved ammunition concentricity. Available only with Toolhead Clamp Kit™ parts pre-installed.
|
 Foam Grip (SKU: T1527)This foam grip cushions your hand yet provides good "feel" when seating primers. Fits both the Plastic and Aluminum Dillon Roller Handles … as well as most other press handles that are approximately 1" diameter and 4" to 5" long. Sold in a 2-Pack.
|
 Light-Load II Shellplate Illuminator (SKU: T1731)Battery-powered LED light illuminates your Dillon RL 550B, XL 650 or XL 750, Hornady Lock-N-Load AP™ or any progressive press with a vacant die mounting hole. ALSO MAKES A GREAT KEYCHAIN OR POCKET FLASHLIGHT! (T1731)
|
 Loaded Round Counter (SKU: T1555)The UniqueTek Loaded Round Counter is an electronic counter for your Dillon press that counts only successfully loaded rounds ... not just press cycles. Can also be used on many other reloading presses that have: 1) Have a Crimp Die with an open top, and 2) Have a primer magazine tube or similar place on which to mount the LCD Display Module.
|
 Micrometer Powder Bar Kit (SKU: T1231)A micrometer conversion kit for the powder bar of your Dillon Auto Powder Measure.
|
 Open End Die Wrench for Dillon Presses (SKU: T1733)An Ope-End Die Wrench for Dillon press. Fits Both 1″ and 1-1/8″ Die Lock Rings. Works on dies where a box-end wrench won't fit. (T1733)
|
 Powder Bar Spacer Bolt Kit (SKU: T1751)Replaces the white plastic Powder Bar Spacer Plugs (#13921) on Dillon Powder Measures. Clamps the Spacer solidly in place … so it can't creep back and forth as the powder bar cycles.4-pk: T1751-S 8-pk: T1752-L |
 Powder Funnel Cleaning Adapter (SKU: T1758)This tool holds Dillon powder funnels so they can be spun up in an electric drill while cleaning brass residue off the tip … greatly speeding up the cleaning process. Fits into any electric drill with a 3/8″ or larger chuck. (T1759) |
 Powder Measure Drain-N-Change Tool (SKU: T1347)Powder Measure Drain-N-Change™ Tool. Allows users of Dillon reloading presses to drain gunpowder or change powder bars without removing the powder measure from the press or toolhead.
|
 Powder Measure Ground Cord (SKU: T1760)This cord grounds your Dillon Powder Measure to bleed off static charge and prevent ESD. It plugs into any grounded outlet. The 8 foot length is sufficient to reach most wall outlets. Includes 2 Powder Measure Harnesses. (T1760)
|
 Powder Measure Quick Change, QD Tab (SKU: T1720)This Powder Measure Quick Change, QD Tab allows you to quickly and easily remove your Dillon powder measure … without any tools!
|
 Powder Measure Stand Adapter (SKU: T1573)The Powder Measure Stand Adapter allows you to store your spare Dillon Powder Measure on a RL550/XL650 Toolhead Stand.**Dillon Toolhead Stand not included. |
 Precision Powder Baffle (SKU: T1278)Pecision Powder Baffle™ upgrade for Dillon powder measures.
|
| 1 | 2 |