| Items: | 0 |
| Subtotal: | $0.00 |
Product List
 .32 Cal. Wad Cutter Powder Funnel (SKU: T1672-05)Specifically designed for loading wad cutter bullets in .32 S&W Long for Bullseye competition. It provides full length case expansion for loading Hollow Base Wadcutter bullets … preventing swaging the bullet base.
|
 .32 Caliber Powder Funnels (SKU: T1672)The Custom Rifle Powder Funnel for .32 cal. pistol cartridges. Smoother interior for smooth powder flow and less powder bridging. Precision machined from top grade 12L14 Steel and hardened to RC55+. |
 .45 HTC Powder Funnel (SKU: T1740)This Powder Funnel was specially designed for loading .45 caliber cast/coated bullets sized to 0.451″ to 0.452″ OD, that would provide for minimum swaging of the bullet’s base and preventing shaving polymer bullet coatings (e.g. Hi-Tek).
|
 .45 HTC Powder Through Expander (SKU: T1729-04)This Powder Through Expander (PTX™) was specially designed for loading .45 caliber cast/coated bullets sized to 0.451″ to 0.452″ OD, that would provide for minimum swaging of the bullet’s base and preventing shaving polymer bullet coatings (e.g. Hi-Tek).
|
 38 Spl. Wadcutter Powder Funnels (SKU: T1735)These Powder Funnels are specially designed for the needs of bullsey shooters loading Double Ended Wad Cutter (DEWC) or Hollow Base Wad Cutter (HBWC) bullets in .38 Special cartridges.
|
 650 FailSafe Bracket Kit (SKU: T1677)This FailSafe Bracket is machined from 1/4″ 303 Stainless Steel. It is very strong and rigid … ensuring that your powder bar returns fully every time. Plus it features a brass shoulder washer that is held in place with set screws … ensuring that the shoulder washer can't disengage from the Failsafe Bracket!
|
 750 FailSafe Bracket Kit (SKU: T1746)This 750 FailSafe Bracket features slotted screw holes that allow the Powder Measure to be rotated enough (about 12 degrees) that the powder bar clears bullet droppers, micrometer seat dies and other extra-tall dies in Stations 3 & 4. from the Failsafe Bracket! At 1/4″ thick, it is very strong and rigid … ensuring that your powder bar returns fully every time.
|
 9mm/.38 HTC Powder Funnel (SKU: T1736)This Powder Funnel was specially designed for loading 9mm cast/coated bullets sized to 0.358″ OD, that would provide for minimum swaging of the bullet’s base. Sized for projectiles up to 0.358″ diameter … preventing shaving polymer bullet coatings (e.g. Hi-Tek).
|
 Brass Primer Magazine Tube Ends (SKU: T1739)These Brass Primer Magazine Tube Ends replace the plastic "Flexible Orifice" on Dillon Primer Magazine Tubes for RL 550 and XL 750 presses.
|
 Custom Powder Funnel (SKU: T1582)The Custom Powder Funnel supplied is precision machined from top grade 12L14 Steel and hardened to RC55+ … offering an almost unlimited life time of use. The mirror finish of this part yields minimal friction and a smoother release.These Custom Powder Funnels work so well, you may want to use them on all your pistol cartridge toolheads … even toolheads that are not set up for a Mr. Bulletfeeder! |
 Extended Die Lock Nuts (SKU: T1745)Extended die lock nuts for when you need to put the die lock nut on the bottom of the toolhead. A 0.155″ shoulder gets the hex nut corners clear of the press frame.
|
Rifle Powder Funnels (SKU: T1632)The Custom Rifle Powder Funnel for .30 cal. rifle cartridges. Smoother interior for smooth powder flow and less powder bridging. Precision machined from top grade 12L14 Steel and hardened to RC55+. |
 Single Stage Powder Die Kit (SKU: T1702)This Custom Powder Die allows you to use Dillon style powder funnels on any single stage press. It also allows you to use 3rd party powder funnels that don't have a set screw groove near the top. It features a threaded cap that allows powder funnel to float. With the Cap removed, it can also be used with a Dillon Powder Measure.
|